1999 Phil Wood Spoke Cutter (Used)
No Image
Category: Tools/Bike Stands
Original Post Date: May-21-2016 8:43:26
Last Repost Date: May-21-2016 8:43:26
Still For Sale: since May 21, 2016 at 8:37
View Count: 619
Watch Count: 2
Last Repost Date: May-21-2016 8:43:26
Still For Sale: since May 21, 2016 at 8:37
View Count: 619
Watch Count: 2
Spoke Cutting and Threading Machine
The Phil Wood Spoke Cutting and Threading Machine is designed and manufactured to provide an invaluable tool to manually size, cut, and place a factory-quality thread on a spoke within a few seconds. The thread is rolled/cold forged onto the spoke, which does not remove material as would occur if the thread were cut into the spoke.
The machine performs through the operation of a manual crank. One revolution of the machine handle both cuts and threads the spoke. It is designed to cut and thread 1.8 mm (15 ga.), 2.0 mm (14 ga.), 2.3 mm (13 ga.) and 2.6 mm (12 ga.) spokes and place 10 mm of 56 tpi thread on the end of each spoke. Please note: Spacers to set the machine to cut 2.3mm (13 ga) and 2.6mm (12 ga) are available, but are not offered as a standard accessory included with the machine.
Our machine is capable of cutting carbon steel, stainless steel, titanium, anodized, and powder coated spokes. Butted and aero spokes can be cut and threaded on the full diameter portion of the spoke. Please be sure to thoroughly clean your machine and dies after cutting and threading powder coated spokes.
The spoke machine die set has two surfaces for cold forging rolled threads onto a spoke. If properly maintained, each surface can roll 60,000 spokes, for a total of 120,000 spokes on a single die set. When cutting and threading standard spokes, some die sets have reached upwards of 160,000 spokes. Lubrication with Phil Tenacious Oil is recommended during the cutting and threading process, applied to the dies every 20 - 30 operations.
Accessories Included with the purchase of a New Spoke Machine:
Spoke Holder - Long
1.8mm Setup Spacer
Spoke Gage & Length Measure Scale
Spoke Cutting & threading Machine Manual
Additional Accessories that can be purchased for your Spoke Machine:
Spoke Machine Vice Mount Assembly
Spoke Cutting & Threading Tray
Straight Pull Spoke Holder
Spoke Machine Dust and Dirt Cover
Spoke Cut Off Guard
Short Spoke Holder
2.3mm Setup Spacer
2.6mm Setup Spacer
A list of a few of the larger corporate users of the Phil Wood Spoke Cutting and Threading Machine:
Campagnolo
Cane Creek
Chris King
DT Swiss
Easton
Euro-Asia Imports
Facebook
Hayes Bicycle Group
HED Cycling
J & B Importers
Paceline
Quality Bicycle Products
Raleigh America
Sapim
Specialized
Spinergy
Shimano
Velocity
The Phil Wood Spoke Cutting and Threading Machine is designed and manufactured to provide an invaluable tool to manually size, cut, and place a factory-quality thread on a spoke within a few seconds. The thread is rolled/cold forged onto the spoke, which does not remove material as would occur if the thread were cut into the spoke.
The machine performs through the operation of a manual crank. One revolution of the machine handle both cuts and threads the spoke. It is designed to cut and thread 1.8 mm (15 ga.), 2.0 mm (14 ga.), 2.3 mm (13 ga.) and 2.6 mm (12 ga.) spokes and place 10 mm of 56 tpi thread on the end of each spoke. Please note: Spacers to set the machine to cut 2.3mm (13 ga) and 2.6mm (12 ga) are available, but are not offered as a standard accessory included with the machine.
Our machine is capable of cutting carbon steel, stainless steel, titanium, anodized, and powder coated spokes. Butted and aero spokes can be cut and threaded on the full diameter portion of the spoke. Please be sure to thoroughly clean your machine and dies after cutting and threading powder coated spokes.
The spoke machine die set has two surfaces for cold forging rolled threads onto a spoke. If properly maintained, each surface can roll 60,000 spokes, for a total of 120,000 spokes on a single die set. When cutting and threading standard spokes, some die sets have reached upwards of 160,000 spokes. Lubrication with Phil Tenacious Oil is recommended during the cutting and threading process, applied to the dies every 20 - 30 operations.
Accessories Included with the purchase of a New Spoke Machine:
Spoke Holder - Long
1.8mm Setup Spacer
Spoke Gage & Length Measure Scale
Spoke Cutting & threading Machine Manual
Additional Accessories that can be purchased for your Spoke Machine:
Spoke Machine Vice Mount Assembly
Spoke Cutting & Threading Tray
Straight Pull Spoke Holder
Spoke Machine Dust and Dirt Cover
Spoke Cut Off Guard
Short Spoke Holder
2.3mm Setup Spacer
2.6mm Setup Spacer
A list of a few of the larger corporate users of the Phil Wood Spoke Cutting and Threading Machine:
Campagnolo
Cane Creek
Chris King
DT Swiss
Easton
Euro-Asia Imports
Hayes Bicycle Group
HED Cycling
J & B Importers
Paceline
Quality Bicycle Products
Raleigh America
Sapim
Specialized
Spinergy
Shimano
Velocity
Warning: This listing is out of date. You must Edit this item before you can repost!"
$3,499 USD
Restrictions: Reasonable offers only, No Trades, Will ship within country only
Sacramento, United States Related Listings
|
|
|
|
|
|
|
|