Sprocket with no Bashguard help :D

PB Forum :: Dirt Jumping & Street
Sprocket with no Bashguard help :D
  • Previous Page
Author Message
flag matago
Posted: May 18, 2008 at 6:28 Quote
I want too have my sprocket without the bashguard but i cannot figure out a way too do this. There is about 1 cm of play because the inserts are too long when i remove the bashguard. Its a raceface sprocket with a e13 bash on raceface diabolusx cranks. Help would be GREAT!
(I hope you understand what i mean, if you have a question ask please)

Unsecure image, only https images allowed: http://img522.imageshack.us/img522/7623/img2463ex1.jpg
flag sean-s-1991
Posted: May 18, 2008 at 6:30 Quote
you can get smaller bolts to hold on the sprocket then u might as well put it on the outside where the bash used to be
flag sean-s-1991
Posted: May 18, 2008 at 6:32 Quote
its better to keep the bash on there though or you keep getting your trousers stuck between the teeth and the chain
flag matago
Posted: May 18, 2008 at 6:33 Quote
Ahh didnt know ya could. What do you mean put it on the outside. Put what on the outside?
flag sean-s-1991
Posted: May 18, 2008 at 6:36 Quote
when you first get the cranks the middle ring sprocket is on the inside of the arm, and either the outer ring or a bashguard is on the other side. -basicly just put the sprocket where the bash was
flag noved
Posted: May 18, 2008 at 6:40 Quote
just keep the bash ring on
flag sharvan
Posted: May 18, 2008 at 6:43 Quote
The chainring bolts are made specifically for use with a bashguard, you either have to get spacers for these bolts, or get bolts made for a single chainring setup.
flag matago
Posted: May 18, 2008 at 6:44 Quote
I just put it on the outside and that did nothing heh, what are them bolts called that i have too buy shorter so i know what too search for.
flag sean-s-1991
Posted: May 18, 2008 at 6:48 Quote
chainring bolts,come in pack of 5, you get them in two sizes. what you want is the single ring bolts Smile
flag sean-s-1991
Posted: May 18, 2008 at 6:49 Quote
and by the way putting the sprocket on the outside makes no difference, it just looks better
flag matago
Posted: May 18, 2008 at 6:54 Quote
These will fit right?
http://cgi.ebay.com.au/Single-Speed-Chain-Ring-BMX-Bike-Chainring-Bolts-FMF-5_W0QQitemZ170210283750QQihZ007QQcategoryZ42317QQrdZ1QQssPageNameZWD1VQQcmdZViewItemQQ_trksidZp1638Q2em118Q2el1247
flag sean-s-1991
Posted: May 18, 2008 at 6:57 Quote
it doesnt say on ebay what size they are and i cant really see from the picture so just go to a bike shop and get some they wont be any more expensive
flag mikedjumpin
Posted: May 18, 2008 at 17:26 Quote
lol just put some washers in there u get em from hope depot for like 50 cents:P
flag sean-s-1991
Posted: May 19, 2008 at 4:43 Quote
yea that's a great idea, i can really see that staying tight LOL lol
flag fujative
Posted: May 19, 2008 at 6:00 Quote
534n wrote:
when you first get the cranks the middle ring sprocket is on the inside of the arm, and either the outer ring or a bashguard is on the other side. -basicly just put the sprocket where the bash was

that will mess up the cain line though, wont it? im pretty sure thats bad for your sprockets and chain.
jsr go to your lbs or maybe even a hardware store and find a few washers that will fit and put those in
  • Previous Page

 


Copyright © 2000 - 2024. Pinkbike.com. All rights reserved.
dv56 0.024304
Mobile Version of Website