Post your Devinci Wilson

PB Forum :: Devinci
Post your Devinci Wilson
Author Message
Posted: Aug 20, 2017 at 15:49 Quote
my full custom devinci wilson

Posted: Aug 20, 2017 at 16:12 Quote
ClickG wrote:
my full custom devinci wilson
Sick baller build!!

Posted: Aug 20, 2017 at 22:24 Quote
Pivot points on wilson

Might be a couple of weird question, but would it be safe to get my pivot hardware (circled) painted or powdercoated? I don`t see any reason it wouldn`t work but I`d rather be safe than sorry.

Other question: Does anyone have any experience with using a angleset to have a slightly slacker headtube angle?

Posted: Aug 21, 2017 at 16:38 Quote
Painted, you'll be fine. Powder coating them might weaken them because of the heat needed to melt the plastic on. But I'm not 100% sure. No comment on the angleset.

Posted: Aug 28, 2017 at 16:07 Quote
hello
what size you would recommend for a 1,84m? i´m thinking in a wilson xp
anyone had problems with the frame?
cheers

Posted: Sep 7, 2017 at 15:39 Quote
I finally painted the pivot hardware on my Wilson. It s not perfect but it looks better than the silver before.

I painted the pivot hardware. It`s not perfect but I really do like it better.

Posted: Sep 9, 2017 at 22:27 Quote
Hi guys I am in trouble for new bike...

I have a summum pro 2011.. And wanna change it.

I have to take a decision between new summum pro 2018 and devinci wilson (don t know if carbon rc or carbon x01 dh)

Pros and cons of wilson? For sure you know it more than me about wilson Wink

Posted: Sep 19, 2017 at 5:51 Quote
Hello guys;

New to this thread, I bought a used 2013 wilson here on pb. Upon inspecting the frame, two chipped areas cought my attention near the bb. I'm new to carbon so I don't know if it's only cosmetic or if it needs to be checked out meticulously, and if it can be repaired.




Posted: Sep 28, 2017 at 16:57 Quote
Hey guys, just wondering. Has anybody noticed some play from the pivot that attaches the wishbone to the control piece? I tightened both bolts on the wishbone which caused some play before, but I just had the linkage rebuilt...

Posted: Sep 28, 2017 at 17:04 Quote
Also, @forest. I would recommend you send the frame to Devinci or bring it in to your local bike shop.

Posted: Sep 28, 2017 at 22:25 Quote
Is it the black bolt? Some blue loctite as well as so.e gorrilla tape next to the entrance area of the bolt to 'preload' it. This is what I did and it removed all play until I sold the bike. I posted pics a few pages back if you need a look

Posted: Oct 8, 2017 at 12:33 Quote
orangeMTBrider wrote:
Hey guys, just wondering. Has anybody noticed some play from the pivot that attaches the wishbone to the control piece? I tightened both bolts on the wishbone which caused some play before, but I just had the linkage rebuilt...

I had this when I rebuild mine. Remove the cranks and tighten the bb carrier a bit more. Not sure what the proper name for it is. Its the bits that screw into the from for your BB to go into.

Posted: Oct 11, 2017 at 3:06 Quote
Does anyone have play in the lower shock mounting bolt? Cranked down and still sloppy

Posted: Oct 11, 2017 at 8:01 Quote
Matt-Levasseur wrote:
Does anyone have play in the lower shock mounting bolt? Cranked down and still sloppy

Put gorrilla tape to act as spacer with a generous amount of loctite on the threads of the wishbone bolt. Hasn t budged in 4months with over 5 park days and many other dh shuttle runs. Pretty stoked this ghetto fix worked knock on wood.

Had this same problem. Ghetto, but never had a problem again.

Blue loctight and gorrilla tape along the outside of where the bolt enters to 'preload' the wishbone. never came loose again after double digits bike park days and 8 months dh riding.


 
Copyright © 2000 - 2018. Pinkbike.com. All rights reserved.
dv56 0.033570
Mobile Version of Website