GT Snow Racer Help

PB Forum :: Mechanics' Lounge
GT Snow Racer Help
Author Message
flag mikedjumpin
Posted: Nov 9, 2008 at 13:41 Quote
khsdjbiker wrote:
is it a common thing for that part to snap?

if its drilled out yes
flag khsdjbiker
Posted: Nov 9, 2008 at 13:43 Quote
mikedjumpin wrote:
khsdjbiker wrote:
is it a common thing for that part to snap?

if its drilled out yes
but if u just leave it and find a pole that fits over top of the gt steerer tube bole u should be ok do u think?
flag mikedjumpin
Posted: Nov 9, 2008 at 13:50 Quote
khsdjbiker wrote:
mikedjumpin wrote:
khsdjbiker wrote:
is it a common thing for that part to snap?

if its drilled out yes
but if u just leave it and find a pole that fits over top of the gt steerer tube bole u should be ok do u think?

unless ur going huge ull be fine ( some thing else would break b 4 that any ways
flag jagarcia89
O+
Posted: Nov 9, 2008 at 20:51 Quote
so with the way that requires no cutting or welding (steer tube from fork over stock steerer) how does it hold there? do you use a quill stem and put it all the way down to through the bike steerer so it wedges in the ski bike steerer??? if so why not just use stem right on there without the bike steer tube
flag
Posted: Nov 9, 2008 at 21:06 Quote
sk8kid33 wrote:
so with the way that requires no cutting or welding (steer tube from fork over stock steerer) how does it hold there? do you use a quill stem and put it all the way down to through the bike steerer so it wedges in the ski bike steerer??? if so why not just use stem right on there without the bike steer tube
because its hard to find a bike stem thats small enough to fit around the GT steerer tube
flag
Posted: Nov 9, 2008 at 21:07 Quote
<Photo does not exist: 2498229>
<Photo does not exist: 2498230>
<Photo does not exist: 2498232>
<Photo does not exist: 2498231>
flag jagarcia89
O+
Posted: Nov 17, 2008 at 21:15 Quote
Do you use an inch or inch and an eigth steer tube over the snow racers steer tube
flag
Posted: Nov 17, 2008 at 21:16 Quote
sk8kid33 wrote:
Do you use an inch or inch and an eigth steer tube over the snow racers steer tube
just found one that fit, and i guess i got lucky Smile
flag blackspire540
Posted: Nov 22, 2008 at 5:38 Quote
https://www.pinkbike.com/photo/2341149/
flag dylaine
Posted: Nov 22, 2008 at 6:34 Quote
blackspire540 wrote:
https://www.pinkbike.com/photo/2341149/
photo

2341149
flag reecer21
Posted: Dec 8, 2008 at 14:41 Quote
does anyone know where I can find a skii for my GT sno racer
flag hondarider17
Posted: Dec 8, 2008 at 14:51 Quote
What i did is this.
I took the steering wheel off.
and i found a piece of pipe that is just a bit Bigger then the steering tubes of the handlebar and stem steerer tube and gt steerer tube, both steering tubes are same diamter, so i stuck the steering tube into the piece of pipe i found bolted it then put it on the gt steering tube.

hope that helped
flag konakid7
Posted: Dec 8, 2008 at 14:53 Quote
yo i would chop the top tube off a bmx or and bike like a couple inches down from the head tube then chop off the head tube on the gt the weld the bike on . and a pair of bmx bars and stem like this : https://www.pinkbike.com/photo/1114542/
flag konakid7
Posted: Dec 8, 2008 at 14:54 Quote
https://www.pinkbike.com/photo/1114542/ or you can find it on the comment above mine Razz

 


Copyright © 2000 - 2024. Pinkbike.com. All rights reserved.
dv42 0.041121
Mobile Version of Website