Sun Ringle Lawhill rear hub -freehub

PB Forum :: Mechanics' Lounge
Sun Ringle Lawhill rear hub -freehub
  • Previous Page
  • Next Page
Author Message
flag joe87
Posted: Dec 27, 2007 at 7:48 Quote
Hello,

I was just riding along and when I pedaled the casset would just spin and no movement from the wheel.
I know the freehub is broke, but how do I fix it?
I tried taking the freehub off, no luck.....
Cant find a place that sells replacment parts for this hub.

Help, Cheers

Joe
flag pbuser102331
Posted: Dec 27, 2007 at 9:43 Quote
could be just your pawls stuck,happened to me a few times now but sorry know idea on parts or how to strip.

do you like it otherwise.
flag joe87
Posted: Dec 28, 2007 at 2:56 Quote
Yea its an amazing hub, this was the first problem I had with it in 4 years.

Any one know how to fix it??
flag t-j-b
Posted: Dec 28, 2007 at 7:55 Quote
yup, you will need:
- A pin spanner or a some similar device that fits in the end of the axle.
- And a ring spanner of about 15mm or something, can't quite remember (trial and error will do it).
Hold the axle still at disc side and undo the driveside nut (cassette removed). The freehub should slide off now, and the axle will pop out. check the state of the springs and pawls and the drive ring teeth. Clean up the internals grease the springs with non-sticky grease and re-assemble.
flag joe87
Posted: Dec 28, 2007 at 8:25 Quote
I did take that drive side nut off, and nothing happened, tried fairly hard to pull the casset off, and then pulled the cir-clips off on both sides and still no budge of the free hub....
flag t-j-b
Posted: Dec 28, 2007 at 8:34 Quote
joe87 wrote:
I did take that drive side nut off, and nothing happened, tried fairly hard to pull the casset off, and then pulled the cir-clips off on both sides and still no budge of the free hub....
Is it all pretty crappy inside? Mine was, needed persausion... Mad
flag joe87
Posted: Dec 28, 2007 at 9:49 Quote
Ah I finally got it, had to get a hammer to it, and off she came!!!!
cleaned up the pawls and springs and bit of grease and its working well so far..

Cheers
flag t-j-b
Posted: Dec 28, 2007 at 9:49 Quote
joe87 wrote:
Ah I finally got it, had to get a hammer to it, and off she came!!!!
cleaned up the pawls and springs and bit of grease and its working well so far..

Cheers
No probs.
flag ride66
Posted: Dec 28, 2007 at 21:05 Quote
I've a side-to-side play in this hub...I don't know what is wrong but it annoy me a lot:S
flag t-j-b
Posted: Dec 29, 2007 at 1:02 Quote
ride66 wrote:
I've a side-to-side play in this hub...I don't know what is wrong but it annoy me a lot:S
strip dwon and re-build usually sorts it out unless its a bearing problem.
flag sye77
Posted: Jul 19, 2009 at 0:17 Quote
what size bearings are they???
flag t-j-b
Posted: Jul 20, 2009 at 2:06 Quote
sye77 wrote:
what size bearings are they???

Take 'em out and measure them... I don't think anyone is gonna know off the top of their head... Measure the OD, ID, and width and go to a bearing shop...
flag sye77
Posted: Jul 20, 2009 at 12:16 Quote
t-j-b wrote:
sye77 wrote:
what size bearings are they???

Take 'em out and measure them... I don't think anyone is gonna know off the top of their head... Measure the OD, ID, and width and go to a bearing shop...
found em... 6002rs, next thing is how to remove the axle???
  • Previous Page
  • Next Page

 


Copyright © 2000 - 2024. Pinkbike.com. All rights reserved.
dv65 0.012892
Mobile Version of Website