NiklTam

Up for sale is my custom Slug Titanium Gravel/ATB Rando Rig. I purchased this frame second hand in the fall of 2023 and it had never been built up to that point. It's a custom frame produced in Taiwan by Slug. I had custom powder coated fenders done in a matte black and powder coated a Steve Potts production fork in the same matte black. The frame was designed around 700x55 tires with fenders, which is how I built it, as pictured. The "for sale" package includes: 1. Slug Ti frame (geo in Pics) 2. Steve Potts unicrown fork, black 3. Honjo custom powdered black fenders 4. White Industries Headset, black 5. Son Edelux II dynamo front light fender mounted 6. Son Seatpost mounted taillight 7. Coax connectors for lighting 8. Thru-axles Frame spec: 1. Headtube. EC34 upper and lower, 1 1/8" steerer 2. T47 external cup BB, 73mm width 3. 12x148 boost rear spacing 4. 12x100 fork spacing 5. flat mount rear brake 6. IS mount front brake 7. external cable routing 8. paragon replaceable derailleur hanger 9. 36t 1x chainring clearance

Refining the quiver and this ones on the block.** I had this frameset handbuilt by Bob at Bantam Bicycles in Portland, OR in the fall of 2022.* Bob has a very detailed eye for classic, but modern bicycles.* His welds are second to none.* I compare the welds on every other bike I see to Bob's work on this bike.* I spec'd the geometry and tubing with the help of Bob and then let him do his thing. ** It employs lightweight and supple tubing, a segmented fork, paragon dropouts, internal dynamo/Di2 routing and high quality wet paint finished in Robins Egg blue with Chocolate brown details.** It was built around 700x55 tires and clears fenders.* I've currently been running it 700x48 slicks and appropriately sized fenders.** The fork has custom dynamo wire retention up the drive-side blade.* There is an internal inlet in the downtube on the drive-side near the headtube for dynamo and/or Di2 wiring.* Wiring runs down the inside of the downtube around the BB and up the seat-tube.* The rear light is custom mounted between the seatstays and the wire exits the seat-tube just behind the light.* *There is a small pin just above the wire hole in the seat-tube to prevent a seatpost from shearing the wire.* The pin can't be seen from the outside.** Can run both cable actuated drivetrains and wired electronic. ETT 61cm HT length 235mm Tt slope 10degrees* BB drop 70mm CS length 450mm HT ext top 25mm ST ext top 25mm Seat tube 59.5cm Fork A to C 420mm Fork Offset 55mm BB - 68mm English Threaded Axles - 12x142 and 12x100 brakes - IS mount Steerer - 1 1/8" straight, EC34 headset seatpost - 27.2mm* crank/chainring - I run it 2x, but did have it setup 1x briefly with a road boost/wide chainline TT pump peg Frameset is in excellent condition with some normal, but minor scuffs. No scores or damage. FOR SALE: Frame, Fork, White Ind Headset, Schmidt SON Edelux II front light, SON taillight, Zefal HPX 4 frame pump. $2500 net Also available: 1. wheels w/ tires> WeAreOne Revive rims, White Ind CLD rear hub, SON 28 front hub, Sapim CX-Ray spokes, Brass nipples, 28h, Rene Herse Hatcher Pass std casing 700x48. $1200 net. 2. Brake Calipers with adapters (qty 2) > Yokozuna Ultimo Silver. $250 net 3. Fenders custom fit for 700x48 tires > Honzo H80 silver $150 Venmo. No Trades.

SQlab 30X Carbon Handlebar, 780mm, 45mm Rise, 12degree backsweep, 4 degree upsweep, 31.8mm clamp - USED excellent condition. Will ship at buyers expense. All sales final.

WHISKY No.9 MTN Boost LT Fork - 29", Post Mount Disc, 15 x 110 mm, 1.5" Tapered Carbon Steerer, Matte Black w/3 pack mounts. Used, has about 100mi on it. few small scuffs but nothing major or structural. Thru-axle and compression plug included. 11" steerer length as pictured. Will ship at buyers expense. All sales final. Specs below: Brake Mount (Fork): Post Mount 160 Wheel Size: 29" , 27.5+ , 29+ Crown Race: 40 Front Axle: 15mm Thru x 110mm Steerer Type: Tapered Offset: 51 Material: Carbon Steerer Tube Length (mm): 280 Color: Matte Carbon Maximum Tire Clearance (Fork): 29 x 3", 27.5 x 3" S.H.I.S. Stem Clamp Diameter: 28.6 Axle to Crown Length: 500 Defined Color: Black