eldrummer

Updated with better pictures. Bought on here this winter thinking I'd burly-up my bike for the coming season, but the project fell through... Who am I kidding, I don't ride hard enough to justify any of this and I other priorities came up, so I'll just stick with my Pike. My loss, your gain. From the previous seller: 29” Manitou Mezzer Pro, currently set to 150mm but internally adjustable from 140mm - 180mm with travel spacers only (don’t need replacement air shafts). Installed spring of 2024, ridden for the season, had lowers serviced fall of 2024, rode again spring 2025 then did lowers and full damper service just before I had a series of non-bike related injuries that kept me mostly off the bike for the summer of 2025. So the guts are in good condition. Dorado MC2 Damper - HS and LS compression, plus Rebound damping adjustments. IRT Air spring - has main air port for positive and negative air chambers (like most forks) and a second air post and piston to adjust the top-out pressure and bottom out characteristics. Brand-new uninstalled bolt on fender included Two travel adjustment pucks plus slick honey grease. Plus other travel pucks inside the fork. Steertube is cut to 18cm (7”) and tapped for OneUp tool. Amazing fork and I love it but I’m old and washed so downsizing my riding in general.

Bought last year thinking I’d wear it daily as a regular watch and that it would double as sports watch… turns out I prefer biking and working out without a watch, and I don’t really care for smartwatches for day to day wear, so I’ll go back to my regular old watch. Excellent condition and works perfectly.

Brand new, never used, tags still attached. Full price for this jacket is 600$. I bought it online for 300 + tx (345$). The medium fit me better, so I decided to go with that one. Unfortunately, I didn’t read the fine print… no returns. Asking 250$ for a quick sale… my loss your gain!

Bought used for an mtb-gravel bike project that ended up going in a different direction. 30.9 diameter (31.6 with the included cane creek shim) 150mm drop external routing No side to side play. Goes up and down perfectly and travel is smooth. Stays in place when « locked » but the actuator is a bit sticky, so the return of the actuator (not of the post itself) can be a bit slow or need a bit of manual help. Could possibly be fixed with a good cleaning of the actuator, or a service.

Bought as a new take off for an mtb-gravel bike project that ended up going in a different direction. I’m selling most parts from the planned conversion so check out my other ads if you need anything else! Barely ridden and in excellent condition. Includes: Sram Rival 1x11 levers with oneup drop bar dropper lever add-on (connected to Guide calipers, more on that below) -- mechanical shifting, hydraulic brakes Sram Rival 11 speed rear derailleur (for up to 42t) Sram Rival 11 speed cassette (11-42t) and chain. Bleed kit and a couple of new sets of Sram brake pads. When I bought the kit, it didn't come with brake calipers, so I installed Guide calipers I was keeping as spares for my mountain bike. This setup is not officially supported by Sram, but worked fine for the few rides I did on the setup... more than decent power and good modulation. From what I could find online, others have successfully run this setup as well, but did experience increasing lever throw as the pads wore due to the piston size difference, so it may require a bit of fiddling from time to time to keep the lever feel spot on. I disconnected the hoses when removing, so it'll need a bleed.

Bought for an mtb-gravel bike project that ended up going in a different direction. Barely ridden and in excellent condition, not a scratch on it. Width: 460mm Reach: 55mm Drop: 100mm Flare: 24 deg

Bought new last year for an mtb-gravel bike project that ended up going in a different direction. I’m selling most parts from the planned conversion so check out my other ads if you need anything else! Barely ridden and in excellent condition. Will come with the flat mount to post mount brake adapter. Steer tube length: 210mm (8.25") Axle to crown: 483mm Hub spacing: 15x110 mm boost Brake mount: flat mount + 20 (Natively uses a 160mm rotor with flat mount caliper. Uses a 180mm rotor with the installed "160mm" flat to post adapter).

Clearing out the parts bin... these haven't seen any use for a while, so time to let them go. I'll post pictures soon. $50 each. Buyer pays shipping. Deity Copperhead - black, 31.8 clamp, 35mm length — SOLD DMR Defy - black, 31.8 clamp, 50mm length - SOLD Chromag Ranger v2 - blue, 31.8mm clamp, 70mm length Generic stem from a Kona Unit - black, 31.8mm clamp, 70mm length ($20)

-- Deity Highside, Black Label and Chromag FU50 are sold -- Too many handlebars in the parts bin, so time to clear them out! Most are in excellent/ close to new condition. The Deity Blacklabel and Chromag Acute are a bit more scratched up, but nothing too crazy. I can provide close-up pictures if needed. $50 each. Buyer pays shipping. Chromag FU50 - 50mm rise, 760mm width, 31.8mm clamp — SOLD Chromag Fubars Acute - 0mm rise, 730mm width, 31.8mm clamp Deity Highside - 80mm rise, 760mm width, 31.8mm clamp -- SOLD Deity BlackLabel - 38mm rise, 760mm width, 31.8mm clamp — SOLD Deity Skywire (carbon) - 15mm rise, 760mm witdh, 35mm clamp I also have few stems I'll be posting soon... we could work out a price if you need one: Chromag Ranger v2 (blue, 31.8mm clamp, 70mm length), Generic from a Kona Unit (black, 31.8mm clamp, 70mm length).