lpatterson

TRP Slate Evo 4 Piston Brakes Like new take-offs from a DH bike. Used for 3 rides. Pads are almost brand new. Rear hose was cut to remove the brake from the bike. A new rear hose has been installed (not shown in photos) but has not been cut to length yet or attached to the lever. Includes a new olive and barb so the hose can be cut, attached, and bled.

Complete set of Hope Tech 4 V4 Brakes (braided lines) & 220mm Hope Vented Rotors. - Includes brand new pads (Hope Red Organic). - Rear brake will need to be bled. - Came off an XL DH bike, so should be lots of hose length for most bikes. - Rear brake hose has a bit of abrasion from a disc rotor that wore away the outer clear coating of the brake line near the caliper (shown in photo). It did not wear into the braided portion of the line at all.

Works components 1 degree angleset (117-124mm headtube length). Used on a Trek Session for approximately one year. - ZS49 Upper Cup, 1-1/8" Bearing - ZS56 Lower Cup, 1-1/2" Bearing - Bearings spin smooth, no play - Includes top cap but no star nut. - Crown Race is for a 1-1/8" steerer tube (used on a dual crown fork). You'll need a new crown race if you want to use it on a tapered steerer tube. - Cups have some visual wear, but function fine and have no play when everything is installed.

Hope Pro 4 32H Rear Hub. Used for about 1 year, all bearings still spin great. - Microspline Driver - 148 x 12 - A few marks on hub flanges, freehub body, and endcaps. Nothing of major concern.

Hope Pro 5 DH 32H Rear Hub. Used for about 6 months of riding. All bearings still spinning smoothly. - XD Driver - Has 157 x 12 endcaps installed. Also includes 150 x 12 endcaps. - Note that this is the DH hub and can only accept a 7 speed cassette.

Brand new shock taken off a Trek Session frame. 250x72.5mm. Has a spacer that can be easily removed to make it 75mm stroke. Includes a 500lb spring.

Rocky Mountain Slayer C70 XL. Carbon front triangle, aluminum rear. 2020-2022 generation in the 2020 black/grey colour. Frame was replaced under warranty at the start of 2024 and ridden for one season. This bike was not ridden in 2025. Parts listed below are either brand new or were ridden for one season if not identified as "new". The bike is a little bit smaller than the current crop of XL bikes. Fork: Rockshox Boxxer Ultimate, 46mm offset. Just serviced. A few small scuffs in the coating of the stanchions but nothing with any real depth. Shock: Rockshox SuperDeluxe Select Plus - New Headset: Hope Stem: Renthal direct mount. Bar: Renthal Fatbar Alloy, 31.8 mm 780 mm width Grips: Deity Supracush - New Seatpost: OneUp V2, 210mm drop. Seat: WTB Volt - New Front Wheel: Bontrager Line 30DH Rear Wheel: WTB HTZ Trail, Bear Pawls BMB-008 Hub. Rim has a slight hop in it. Front Tire: Maxxis Assegai 29x2.5 DH 3C MaxxGrip - Lots of life left. Rear: Maxxis Shorty 27.5x2.4 DH 3C MaxxGrip - 70% life left. Brakes: Sram DB8, 220mm/200mm rotors - New. Shifter: Sram NX- New Derailleur: Sram NX - New Cassette: Sram NX -New Cranks: Raceface Turbine, 165mm - New Chainring: Chromag Sequence 30T BB: Raceface Chainguide: Rocky Spirit Guide Pedals: HT X1 Comes with extra frame hardware.

Brand new OneUp V3 dropper post. 31.6 Diameter 240mm Travel Thought I could fit a 240mm drop in my frame, but had to go 210mm instead so this one is for sale. Took it out of the box, test fit it, and put it back in the box. Does not include cable or remote, post only.

RockShox Vivid Select - 230 x 65 Take off from 2024 Norco Range VLT A1. Purchased last September and ridden for 2-3 months before I switched to coil. Appears to have a very small nick in the clearcoat of the air shaft around 10% travel (see in photos). Has external rebound and HBO adjustments. Has bushings installed but no shock hardware included.